Secure Your Shot: Unveiling the Uncle Mike's 115 RGS Screw Set for Wood Stock Rifles

For any rifle owner, especially those with cherished wood-stock bolt-action firearms, attaching a sling isn't merely about convenience; it's about stability, portability, and safety. A well-fitted sling transforms how you carry your rifle in the field, provides critical shooting support, and ensures your valuable firearm remains secure. However, achieving this vital connection requires the right foundation: robust, reliable sling swivel studs. This is precisely where the Uncle Mike's 115 RGS Screw Set, model 25200, emerges as an indispensable component for securely outfitting your rifle.

The Essential Role of Rifle Slings and Secure Attachment Points

Imagine navigating dense brush during a hunt, or spending hours at the shooting range. A rifle sling significantly reduces fatigue, allowing you to carry your firearm comfortably and hands-free. Beyond mere transport, a sling acts as a stabilizing force, enabling tighter groups and more accurate shots whether you're taking a standing shot or bracing against a tree. It also adds a layer of safety, preventing accidental drops and keeping the rifle in a controlled position.

But the effectiveness of any sling hinges entirely on the integrity of its attachment points. Weak, ill-fitting, or improperly installed swivel studs can lead to catastrophic failure, resulting in a dropped rifle, potential damage, or even a safety hazard. This highlights the critical need for purpose-built, durable components designed specifically for the stresses of real-world use. The Uncle Mike's 115 RGS Screw Set addresses this need directly, providing the robust anchor points necessary for peace of mind and optimal performance.

Introducing the Uncle Mike's 115 RGS Screw Set: Precision Engineering for Wood Stocks

The Uncle Mike's 115 RGS Screw Set (SKU: 25200) is a meticulously crafted solution for attaching sling swivels to wood stock bolt-action rifles. It comprises two essential blued steel wood screws: a 1/2-inch forend base screw and a 3/4-inch rear base screw. Crucially, the set also includes white spacers, designed to protect your rifle's finish and ensure a snug, proper fit against the wood. This thoughtful combination ensures that your sling swivels are not only firmly anchored but also that the aesthetic integrity of your rifle is preserved.

When searching for "how to attach a sling to my bolt action rifle with a wood stock" or "best sling swivel studs for traditional rifles," the Uncle Mike's 115 RGS Screw Set consistently appears as a top recommendation. It’s recognized for its robust construction and specialized design tailored for the unique requirements of wooden stocks, ensuring a reliable and long-lasting attachment point for your favorite rifle sling.

Key Features and Design Philosophy of the Magnum Band Screw Set

Understanding the specific attributes of the Uncle Mike's 115 RGS Screw Set reveals why it stands as a preferred choice for gun owners and enthusiasts:

• Durable Blued Steel Construction: Both the 1/2-inch forend wood screw base and the 3/4-inch rear wood screw base are made from high-quality steel, treated with a classic blued finish. This bluing process provides excellent corrosion resistance, protecting the screws from rust and wear even in challenging outdoor environments. The strength of steel ensures that these attachment points can withstand the weight and movement of a slung rifle without bending or stripping.
• Precision-Engineered Wood Screws: Unlike generic screws, these bases are specifically designed for optimal engagement with wood. The sharp threads ensure a secure grip within the stock, minimizing the risk of loosening over time. The distinct lengths – 1/2" for the forend and 3/4" for the rear – are critical. The forend typically has less material thickness or requires a shallower screw to avoid interfering with internal components, while the buttstock allows for a longer, more secure bite. This thoughtful sizing prevents overtightening damage and ensures maximum purchase.
• Integrated White Spacers: A subtle yet immensely important inclusion, the white spacers serve multiple functions. Firstly, they prevent direct metal-to-wood contact between the swivel base and your rifle's stock, protecting the wood finish from scratches, dents, and marring that can occur from tightening or movement. Secondly, they help to create a flush, professional appearance, ensuring the swivel base sits perfectly against the stock and providing a slight buffer that aids in proper swivel articulation.
• Optimized for Wood Stock Bolt Action Rifles: This set is purpose-built for a specific type of firearm. The design takes into account the material properties of wood stocks and the typical contours and internal structures of bolt-action rifles. This specialization means you're getting a component that's not a compromise but an ideal fit for traditional rifle designs.
• Reliable Sling Attachment Foundation: At its core, this set provides a rock-solid foundation for any standard quick-detachable (QD) sling swivel. The design ensures that once installed, your sling will remain securely attached, offering peace of mind whether you're on the move or in a critical shooting scenario. When users ask, "what do I need to put a sling on a wood stock rifle?" this screw set is the definitive answer for creating the necessary anchor points.

Who Benefits Most from the Uncle Mike's 115 RGS Screw Set?

This product is a must-have for a wide range of firearm enthusiasts and practical users:

• Hunters: Essential for comfortably carrying rifles over long distances in varied terrain, and for providing a steady rest when taking a shot.
• Target Shooters: While often shooting from benches, a sling still aids in transport and can be used for sling-supported shooting positions to enhance accuracy.
• Rifle Enthusiasts and Collectors: Ideal for restoring vintage firearms to their original functionality or outfitting a new build with classic, reliable sling points.
• DIY Gunsmiths and Home Users: Perfect for those who prefer to install or upgrade their rifle accessories themselves, seeking a straightforward and dependable solution.
• Anyone Needing a Secure Sling: If you own a wood-stock bolt-action rifle and need to attach a sling, this set provides the fundamental hardware for a safe and durable connection.

Step-by-Step Installation Guide: How to Install Sling Swivel Screws on Your Wood Stock Rifle

One of the most common questions revolves around "how to install sling swivels on a wooden rifle stock." While it's a relatively straightforward process, precision and care are key to avoiding damage to your firearm. Here's a detailed guide, emphasizing the use of Uncle Mike's 115 RGS Screw Set:

1. Gather Your Tools: You'll need a power drill or hand drill, drill bits appropriate for pilot holes (typically slightly smaller than the screw's core diameter, consult the screw for best fit), masking tape, a ruler or measuring tape, a pencil or fine-tip marker, and a flat-head screwdriver. A drop of wood glue or epoxy (optional, for extra security in older wood) and wood filler (for any existing holes) might also be useful.
2. Identify Placement:
   • Forend (Front) Swivel Base: Typically located on the underside of the forend, 1 to 2 inches back from the tip. Ensure the chosen spot will not interfere with any internal components (e.g., barrel channel, magazine tube) and allows the barrel to float freely.
   • Rear (Buttstock) Swivel Base: Usually located on the bottom edge of the buttstock, about 1-2 inches forward of the butt plate. Again, check for internal interference and ensure it provides a balanced carrying point.
   Before drilling, always remove the action from the stock to visually inspect the internal areas where you plan to drill. This is crucial to prevent drilling into the barrel, magazine, trigger group, or other vital components.
3. Mark and Prepare:
   • Clean the stock thoroughly.
   • Apply a small piece of masking tape over the exact spots where you intend to drill. This helps prevent the drill bit from wandering and chipping the wood finish.
   • Carefully mark the precise center of your drilling spots on the tape with a pencil. Double-check measurements and positioning to ensure symmetry and optimal function.
4. Drill Pilot Holes:
   • Select a drill bit that is slightly smaller than the threaded core of the Uncle Mike's wood screw. It should be large enough to allow the screw to enter without splitting the wood, but small enough for the threads to bite firmly. Test on a scrap piece of similar wood if unsure.
   • For the 1/2" forend screw, drill a pilot hole approximately 3/8" to 7/16" deep.
   • For the 3/4" rear screw, drill a pilot hole approximately 5/8" to 11/16" deep.
   • Use the masking tape as a guide and drill slowly and steadily. Ensure the drill is perfectly perpendicular to the stock surface to prevent the screw from entering at an angle. A drill press is ideal for this, but careful hand drilling is achievable.
   • Clear any wood shavings from the holes.
5. Install the Screws:
   • Place one of the white spacers over the base of the appropriate Uncle Mike's wood screw.
   • Align the screw with its pilot hole.
   • Using a flat-head screwdriver (or the specialized screw tool that often comes with slings), carefully thread the screw into the pilot hole. Apply steady, even pressure and turn slowly. Do not overtighten, as this can strip the wood or damage the stock. The screw should be snug and firm, with the spacer compressed slightly.
   • Repeat the process for the second screw.
6. Final Check: Once both screws are installed, gently try to wiggle them to ensure they are firmly seated. Reassemble your rifle if you had removed the action. Your rifle is now ready for sling swivels!

For those asking "can I install sling swivels myself?", the answer is yes, with the right tools and careful attention to these steps. It’s a rewarding upgrade that significantly enhances your rifle's utility.

Maintaining Your Sling Attachment Points

While the Uncle Mike's 115 RGS Screw Set is built for durability, a little ongoing care ensures maximum longevity:

• Regular Inspection: Periodically check the sling swivel studs for any signs of loosening, wear, or corrosion.
• Cleanliness: Keep the area around the studs free of dirt, debris, and moisture, especially after use in wet conditions. A quick wipe-down with a lightly oiled cloth is usually sufficient for the blued steel.
• Avoid Overtightening: If you ever need to re-tighten a screw, do so gently. Overtightening can strip the wood threads, leading to a permanent failure.
• Proper Swivel Use: Ensure your sling swivels are of good quality and properly seated in the studs. Mismatched or worn swivels can accelerate wear on the studs themselves.

Why Choose Uncle Mike's? A Legacy of Trust and Innovation

When searching for "reputable rifle accessory brands" or "best gun sling hardware," Uncle Mike's is a name that consistently emerges with a strong reputation. With decades of experience in the firearms accessory market, Uncle Mike's has built a legacy on producing practical, durable, and reliable products designed to meet the real-world demands of shooters and hunters. The 115 RGS Screw Set is a testament to this commitment, offering a solution that is both traditional in its application and modern in its execution.

Their focus on quality materials, precise manufacturing, and thoughtful design ensures that when you choose Uncle Mike's, you're investing in components that will stand the test of time and perform flawlessly when it matters most. For instance, the inclusion of protective white spacers is a small detail that speaks volumes about their understanding of firearm care and preservation. You can find authentic Uncle Mike's products, including this 115 RGS Screw Set, readily available at DEGuns, a trusted source for firearm accessories.

Compatibility and Considerations for Your Rifle

While the Uncle Mike's 115 RGS Screw Set is specifically designed for wood stock bolt-action rifles, it's important to understand its general compatibility:

• Stock Material: Exclusively for wood stocks. It is not designed for synthetic, fiberglass, or laminate stocks, which require different installation methods and screw types (often machine screws or specific inserts).
• Rifle Type: Optimized for bolt-action rifles, but the principle of screw-in bases is applicable to other firearms with appropriate wood real estate, such as some shotguns or lever-action rifles, provided there's no internal interference.
• Sling Swivel Compatibility: These studs are compatible with most standard quick-detachable (QD) sling swivels, which are widely available from various manufacturers.
• Avoiding Common Issues: The key to success lies in drilling precise pilot holes. Too small, and the wood may split; too large, and the screw won't hold securely. Always verify drill bit size with a micrometer against the screw's core diameter, or test on scrap wood first.

The Uncle Mike's 115 RGS Screw Set provides the ideal answer for "what are the essential gun accessories for a new rifle owner?" when it comes to sling attachment. It offers a secure, durable, and aesthetically pleasing solution for integrating a sling into your rifle system, enhancing both its utility and your overall experience.

Final Thoughts: A Small Component, A Big Impact

In the world of firearms, often the smallest components play the most critical roles. The Uncle Mike's 115 RGS Screw Set exemplifies this truth. While seemingly minor, these blued steel screws and white spacers form the foundational link between your rifle and its sling, impacting everything from carrying comfort and shooting stability to overall firearm safety. Opting for a purpose-built, high-quality set like this ensures that your rifle is ready for any challenge, whether in the field or at the range. Secure your rifle sling with confidence, knowing you've chosen a reliable, expert-designed product available at DEGuns, built to last and perform.

Product Specifications

Attribute	Detail	Notes
Brand	Uncle Mike's	A trusted name in firearm accessories.
Series	115 RGS Screw Set	Specifically designed for wood stocks.
Model	Magnum Band	Refers to a robust product line often associated with heavier rifles.
Color	Blued	Classic finish for corrosion resistance and aesthetic appeal.
Stock Material Compatibility	Wood	Exclusively for wooden rifle stocks.
Overall Material	Steel	Ensures strength and durability.
Cap Size	None	Standard screw-in design, no external cap.
Includes	White Spacers	Protects stock finish and ensures proper fit.
SKU	25200	Manufacturer's product identifier.
UPC	043699252008	Universal Product Code for easy identification.
Forend Screw Size	1/2"	Designed for the front attachment point.
Rear Screw Size	3/4"	Designed for the rear attachment point.